Category: Road Marker Store

Select the marker color and quantity below. Our reflective road markers are available with or without a melt down adhesive pad. Contact us with any questions.

Click Here to go to our product ordering page.  

Our Yellow/Red Model C80 markers from Stimsonite combine the durability of an ABS high strength shell and advanced optics to create one of the toughest and brightest Raised Pavement Markers in the industry.

The Yellow/Red C80 Raised Pavement / Road Markers on this page are “two way” and are reflective from both directions. They are used to show yellow to cars going the correct way on a one way street and red to cars going the wrong way. The markers measure 4″ x 4″ and are slightly less than 3/4″ tall. In high-intensity traffic conditions, abrasion resistance is crucial to extending the service life of the marker. Our C80 markers include a long-life abrasion resistant coating to enhance the retained reflectivity of the marker. This provides the safest delineation to drivers in critical wet-night conditions

The markers can be applied to asphalt or cement road surfaces using our Melt Down Thermoplastic Pads.  You can also purchase epoxy locally and apply them.  For wooden surfaces like railroad ties you can drill through the middle of the marker and screw them down.  For large application areas you can also use hot tar.

We sell the Yellow and Red  C80 Markers in 2 configurations.  Marker only,  and marker with melt down thermoplastic pad. (See picture at bottom of page)

Our melt down 5 x 5 thermoplastic pads are more permanent.  To install just heat the surface, lay down the pad, continue heating until the pad is melted and then lightly press the marker into the center of the thermoplastic and let cool.

The markers can be applied to asphalt or cement road surfaces using our Melt Down Thermoplastic Pads. You can also purchase epoxy locally and apply them. For wooden surfaces like railroad ties you can drill through the middle of the marker and screw them down. For large application areas you can also use hot tar.

We sell the Yellow and Red C80 Markers in 2 configurations. Marker only and Marker with melt down thermoplastic pad. (See picture at bottom of page)

Click Here to go to our product ordering page.  

Our White/Red Model C80 markers from Stimsonite combine the durability of an ABS high strength shell and advanced optics to create one of the toughest and brightest Raised Pavement Markers in the industry.

The White/Red C80 Raised Pavement / Road Markers on this page are “two way” and are reflective from both directions.  They are used to show white to cars going the correct way on a one way street and red to cars going the wrong way. The markers measure 4″ x 4″ and are slightly less than 3/4″ tall. In high-intensity traffic conditions, abrasion resistance is crucial to extending the service life of the marker. Our C80 markers include a long-life abrasion resistant coating to enhance

The markers can be applied to asphalt or cement road surfaces using our Melt Down Thermoplastic Pads.  You can also purchase epoxy locally and apply them.  For wooden surfaces like railroad ties you can drill through the middle of the marker and screw them down.  For large application areas you can also use hot tar.

We sell the White and Red C80 Markers in 2 configurations.  Marker only,  and marker with melt down thermoplastic pad. (See picture at bottom of page)

Our melt down 5 x 5 thermoplastic pads are more permanent.  To install just heat the surface, lay down the pad, continue heating until the pad is melted and then lightly press the marker into the center of the thermoplastic and let cool.

Click Here to go to our product ordering page.  

Our Green Model C80 markers from Stimsonite combine the durability of an ABS high strength shell and advanced optics to create one of the toughest and brightest Raised Pavement Markers in the industry.

Green markers normally designate that an area is “OK” for traffic. The Green C80 Raised Pavement / Road Markers on this page are “two way” and are reflective from both directions. The markers measure 4″ x 4″ and are slightly less than 3/4″ tall. In high traffic areas, abrasion resistance is crucial to extending the service life of the marker. Our C80 markers include a long-life abrasion resistant coating to extend the reflectivity of the marker over time. This provides the safest delineation to drivers in critical wet-night conditions.

The markers can be applied to asphalt or cement road surfaces using our Melt Down Thermoplastic Pads.  You can also purchase epoxy locally and apply them.  For wooden surfaces like railroad ties you can drill through the middle of the marker and screw them down.  For large application areas you can also use hot tar.

We sell the Green C80 Markers in 2 configurations.  Marker only,  and marker with melt down thermoplastic pad. (See picture at bottom of page)

Our melt down 5 x 5 thermoplastic pads are more permanent.  To install just heat the surface, lay down the pad, continue heating until the pad is melted and then lightly press the marker into the center of the thermoplastic and let cool.

Click Here to go to our product ordering page.  

Our Red Model C80 markers from Stimsonite combine the durability of an ABS high strength shell and advanced optics to create one of the toughest and brightest Raised Pavement Markers in the industry.

Red markers are typically used to mark areas where cars or vehicles are prohibited. The Red C80 Raised Pavement / Road Markers on this page are “two way” and are reflective from both directions. The markers measure 4″ x 4″ and are slightly less than 3/4″ tall. In high-intensity traffic conditions, abrasion resistance is crucial to extending the service life of the marker. Our C80 markers include a long-life abrasion resistant coating to enhance the retained reflectivity of the marker. This provides the safest delineation to drivers in critical wet-night conditions.

The markers can be applied to asphalt or cement road surfaces using our Melt Down Thermoplastic Pads.  You can also purchase epoxy locally and apply them.  For wooden surfaces like railroad ties you can drill through the middle of the marker and screw them down.  For large application areas you can also use hot tar.

We sell the Red C80 Markers in 2 configurations.  Marker only,  and marker with melt down thermoplastic pad. (See picture at bottom of page)

Our melt down 5 x 5 thermoplastic pads are more permanent.  To install just heat the surface, lay down the pad, continue heating until the pad is melted and then lightly press the marker into the center of the thermoplastic and let cool.

Click Here to go to our product ordering page.  

Our White Model C80 markers from Stimsonite combine the durability of an ABS high strength shell and advanced optics to create one of the toughest and brightest Raised Pavement Markers in the industry.

The White C80 Raised Pavement / Road Markers on this page are “two way” and are reflective from both directions. The markers measure 4″ x 4″ and are slightly less than 3/4″ tall. In high-intensity traffic conditions, abrasion resistance is crucial to extending the service life of the marker. Our C80 markers include a long-life abrasion resistant coating to enhance the retained reflectivity of the marker. This provides the safest delineation to drivers in critical wet-night conditions.

The markers can be applied to asphalt or cement road surfaces using our Melt Down Thermoplastic Pads.  You can also purchase epoxy locally and apply them.  For wooden surfaces like railroad ties you can drill through the middle of the marker and screw them down.  For large application areas you can also use hot tar.

We sell the White C80 Markers in 2 configurations.  Marker only,  and marker with melt down thermoplastic pad. (See picture at bottom of page)

Our melt down 5 x 5 thermoplastic pads are more permanent.  To install just heat the surface, lay down the pad, continue heating until the pad is melted and then lightly press the marker into the center of the thermoplastic and let cool.

Click Here to go to our product ordering page.  

Our Yellow Model C80 markers from Stimsonite combine the durability of an ABS high strength shell and advanced optics to create one of the toughest and brightest Raised Pavement Markers in the industry.

The Yellow C80 Raised Pavement / Road Markers on this page are “two way” and are reflective from both directions. The markers measure 4″ x 4″ and are slightly less than 3/4″ tall. In high-intensity traffic conditions, abrasion resistance is crucial to extending the service life of the marker. Our C80 markers include a long-life abrasion resistant coating to enhance the retained reflectivity of the marker. This provides the safest delineation to drivers in critical wet-night conditions.

The markers can be applied to asphalt or cement road surfaces using our Melt Down Thermoplastic Pads.  You can also purchase epoxy locally and apply them.  For wooden surfaces like railroad ties you can drill through the middle of the marker and screw them down.  For large application areas you can also use hot tar.

We sell the Yellow C80 Markers in 2 configurations.  Marker only,  and marker with melt down thermoplastic pad. (See picture at bottom of page)

Our melt down 5 x 5 thermoplastic pads are more permanent.  To install just heat the surface, lay down the pad, continue heating until the pad is melted and then lightly press the marker into the center of the thermoplastic and let cool.

Click Here to go to our product ordering page.  

Our Blue Model C80 markers from Stimsonite combine the durability of an ABS high strength shell and advanced optics to create one of the toughest and brightest Raised Pavement Markers in the industry.  Blue markers are typically used to mark fire hydrants.  The Blue C80 Raised Pavement / Road Markers on this page are “two way” and are reflective from both directions. The markers measure 4″ x 4″ and are slightly less than 3/4″ tall. In high-intensity traffic conditions, abrasion resistance is crucial to extending the service life of the marker. Our C80 markers include a long-life abrasion resistant coating to enhance the retained reflectivity of the marker.  This provides the safest delineation to drivers in critical wet-night conditions.

The markers can be applied to asphalt or cement road surfaces using our Melt Down Thermoplastic Pads.  You can also purchase epoxy locally and apply them.  For wooden surfaces like railroad ties you can drill through the middle of the marker and screw them down.  For large application areas you can also use hot tar.

We sell the Blue C80 Markers in 2 configurations.  Marker only,  and marker with melt down thermoplastic pad. (See picture at bottom of page)

Our melt down 5 x 5 thermoplastic pads are more permanent.  To install just heat the surface, lay down the pad, continue heating until the pad is melted and then lightly press the marker into the center of the thermoplastic and let cool.